With over 10,000 orders
With over 10,000 orders
Replacement wheels for your 60" deck that had the 1/2" bolt and hard plastic wheels. These are premium wheels with hard rubber compound on the outs...
View full detailsThis is a new reproduction 3 pin clutch driver for manual transmission Cub Cadets. Heavy duty .179 backer with machined hub and oilite iron bronze ...
View full detailsThese are the lift straps for putting a 450 451 snowblower onto an SGT. UNPAINTED.
This is a tie rod upgrade to the 82 series and quite a few tractors following it. It is not for the SGT's. Will work with power steering. Rod is .3...
View full detailsThe Cub Cadet Adjustable Height Removable Hitch bolts onto cast iron or aluminum rear ends above the stock plate, allowing you to easily adjust the...
View full detailsThe Cub Cadet Bolt On Rear Hitch replaces your old factory bolt-on hitch with a new 1/4" thick model featuring an extra hole designed for a 3/4" sh...
View full detailsThe Cub Cadet Bolt On Receiver Hitch is a heavy-duty, versatile hitch designed for newer series Cub Cadets with aluminum rear end housings. It feat...
View full detailsJust like the original ones, (CC-34-013) but 1.5" longer. Allows you to run equipment that is lower to the ground.
Connects the 3 point rock shaft arms to the lift arms. 5/8" - Cat. 0 ball sockets, 5/8 threaded shaft. Sold each. Similar to Cub Cadet #703-0814
Connects the 3 point rock shaft arms to the lift arms. 5/8" - Cat. 0 ball sockets, 5/8 threaded shaft. 5/8 Furrels. Exact Replicas. Sold as a set. ...
View full detailsConnects the 3 point to the hydraulic cylinder. 82 Series, Spread Frames - Unpainted. Similar to Cub Cadet #703-0811 CC-03-007B would fit the Super...
View full detailsConnects the 3 point to the hydraulic cylinder. 82 Series, Spread Frames - Unpainted. Similar to Cub Cadet #703-0811 CC-03-007B would fit the Super...
View full detailsThis is a new clutch disk for manual transmission Cub Cadets. Made from T1 Steel for long life. PN# CC-33-006
Replacement Cam for the Deck Lift. Typically on the right side of the tractor. Unpainted. PN# CC-96-064
We took and made some step pad blanks out of 16 ga. steel and then ran them thru the Powder Coating Booth and covered them with Endura Step Texture...
View full detailsFits 38" - 50" decks. Weld on kit similiar to Cub Cadets Origianl Kit - you add wheels. UNPAINTED. PN# CC-09-001
Reproduction of the Amp Meter Bracket issued by Cub Cadet. UNPAINTED PN# CC-98-031
Bracket for the cub cadet original for attaching the choke cable. UNPAINTED. PN# CC-71-061
Original Cub Cadet Deck Pulley Cover. OEM Specs. Sold UNPAINTED. Per pair.
Original Cub Cadet Deck Wheel Bracket. OEM Specs. Sold in pairs. UNPAINTED. PN# CC-71-056
Original Cub Cadet Deck Wheel Bracket Mount. OEM Specs. Sold in pairs, left and right. UNPAINTED PN# CC-72-055
Reproduction Fenders for the Cub Cadet Original - Since these fenders are hard to find, I have created a "Looks Pretty Close" set. Bolts to the sea...
View full detailsReproduction Fenders Rod for our Original Fenders and Reproduction ones we sell. 5/16" rod. UNPAINTED. PN# CC-21-006
Original Cub Cadet Front Frame Cover. OEM Specs. Sold UNPAINTED. PN# CC-71-054
{"one"=>"Select 2 or 3 items to compare", "other"=>"{{ count }} of 3 items selected"}