More Website Templates @ TemplateMonster.com - November 14, 2011!

Snowblower and Snow Thrower Parts


QA Belt Tension Assembly

QA36 / QA 42 / QA36A / QA42A belt tensioner bolt, castle nut & furrell.  This style has a welded nut in the end for use with 3/4" wrench.  This is the 1/2-13 LEFT hand threaded adjuster bolt.

PN# CC-86-031    $38.00

 


 

QA Bolt Tabs

Pair of straps for the front of the QA mounts.    No more fumbling with bolts, nuts and washers.    Slide these in the hole and secure with a 1/2-13 bolt in the factory welded nut inside the frame.

PN# CC-96-504     $23.00/pr.

 

QA Belt Tension Bolt

QA36 / QA 42 / QA36A / QA42A belt tensioner bolt and castle nut.  This style has a welded nut in the end for use with 3/4" wrench.  This is the 1/2-13 LEFT hand threaded adjuster bolt.

PN# CC-86-030    $24.00



Gear Box Shaft Short - A

90 degree gear box shafts for Cub Cadet Tillers and Snow Throwers.  Made from 4140 P Alloy Steel.  Keyways and snap ring groves.  4 1/8" Long x 3/4" dia. , Snap ring groves 2 7/8" apart.

PN# CC-86-033    $55.00

 

Gear Box Shaft Short - B

90 degree gear box shafts for Cub Cadet Tillers and Snow Throwers.  Made from 4140 P Alloy Steel.  Keyways and snap ring groves.  4 21/64" Long x 3/4" dia. , Snap ring groves 2 11/16" apart.

PN# CC-86-034    $55.00

 

Gear Box Shaft Long

90 degree gear box shafts for Cub Cadet Tillers and Snow Throwers.  Made from 4140 P Alloy Steel.  Keyways and snap ring groves.  5 1/2" Long x 3/4" dia.

PN# CC-86-035   $58.00

 

QA Transfer Shaft

Transfer shaft for the QA snowblowers.

PN# CC-86-036    $56.00

 

Cub Cadet 450/451 Lift Straps

These are the lift straps for the 450 / 451 snowblower that you will need when putting a 450/451 onto a Super Garden Tractor.

PN# CC-78-051    $24.00

 

Snow Thrower Skids with Feet - Double Sided

Double sides snow thrower skid shoes.  Just might be the last set of skid shoes that you need to buy!  For models BB36, CW36, QA36, QA36A, QA42A, QA36B, QA42B. UNPAINTED.

Replaces Cub Cadet PN# IH-475565-R1  USE IH-475565-R2

XMW PN# CC-25-002     $62.00

 

Implement Lift Rod - 28 1/2"

Implement lift rod.  For lifting push  blades, snowblowers, etc.  1/2" dia with 1/8" holes on each end for clip.  UNPAINTED.

PN# CC-67-001    $20.00

 


  • Implement Lift Rod - 34 1/2"

  • Implement lift rod.  For lifting push  blades, snowblowers, etc.  1/2" dia with 1/8" holes on each end for clip.  UNPAINTED.

    PN# CC-67-002    $24.00

 

Adjustable Lift Rod - 28"

Adjustable lift rod provides 2.5" of travel on the adjuster nut end.  The rod can be adjusted from 25.5" to 30.5", covering the factory lift rods of 28".  Adjustable end with locking nut. Threaded shaft end is stainless steel so you do not have to paint the threads or worry about corrosion.  Sold UNPAINTED.

PN# CC-96-016     $28.00

 

Adjustable Lift Rod - 32"

Adjustable lift rod provides 2.5" of travel on the adjuster nut end.  The rod can be adjusted from 29.5" to 34.5", covering the factory lift rods of 32".  Adjustable end with locking nut. Threaded shaft end is stainless steel so you do not have to paint the threads or worry about corrosion.  Sold UNPAINTED.

PN# CC-96-017    $32.00

 


  • Snow Thrower Auger Rotor Repair Kit

  • Repair your worn out shaft and sprocket with this repair kit.  Similar to IH-397031-R1.  Shaft is welded to sprocket. Fits QA-36 and QA-42.  UNPAINTED

    CC-86-010    $85.00

 

Snow Thrower Auger Rotor 24 Tooth #40 Sprocket

Snow Thrower auger rotor 24 tooth #40 sprocket.  This is laser cut from 1/4" stainless steel.  Heated to 500 degrees and quenched.  1" diameter hole.  Fits QA-36 and QA-42. UNPAINTED

CC-86-011    $45.00

 

Snow Thrower Auger Rotor 24 Tooth #40 Sprocket with Holes

Snow Thrower auger rotor 24 tooth #40 sprocket.  This is laser cut from 1/4" stainless steel.  Heated to 500 degrees and quenched.  1" diameter hole.  Has 3 - 3/8" holes for plug welds or for bolting applications.  Fits QA-36 and QA-42. UNPAINTED

CC-86-012    $45.00

 


  • Snow Thrower Auger Rotor 24 Tooth #40 Sprocket With Slots

  • Snow Thrower auger rotor 24 tooth #40 sprocket.  This is laser cut from 1/4" stainless steel.  Heated to 500 degrees and quenched.  1" diameter hole.  Has 3 - 3/8" slots for plug welds or for bolting applications.  Fits QA-36 and QA-42. UNPAINTED

    CC-86-013    $45.00

 

Snow Thrower Auger Rotor Repair Shaft

1" snow thrower stub shaft for repairing your auger tube.  Fits QA-36 and QA-42. UNPAINTED

CC-86-014    $22.00

 

Snow Thrower Auger Rotor Centering Washer

This is the centering washer that fits inside the auger rotor tube.  Typically need 2.  Sold as each.  Fits QA-36 and QA-42. UNPAINTED

CC-86-015    $11.00

 


  • Snow Thrower Auger Rotor Spacer Washer

  • This is the spacer that goes between the outer centering washer and the sprocket.  Fits 1" shaft.  Fits QA-36 and QA-42. UNPAINTED

    CC-86-016    $11.00

 

NF and WF Lift Bracket Extender

Lift bracket extender bolts to your lift ear on your NF and WF cub cadets.   Multi holes allow you to position your lift rod to obtain higher lift amounts.  Knee action of the extender allows the blower or blade to float if needed, allowing you to leave your float lock in if needed.  Works great in combination with CC-96-016 Below. UNPAINTED

CC-96-015    $26.00

 


450/451 Snow Blower Spring Assist

Spring assist for the 450 / 451 snowblowers.  Bolts tot he bottom of the frame.  On spread frames and newer, attaches using existing bolts and holes.  Adjustable eye bolt for adjusting tension.  Just like the kit originally sold by Cub Cadet for this setup. UNPAINTED

CC-94-001    $135.00

 


  • Snow Blower Lift Bracket 450/451 on Regular Cub Cadet

  • Lift bracket for adding a 450 / 451 / 551 to a 82 series or even older cub cadet.  Makes your tractor from a pull to lift to a push to lift like the Super Garden Tractors. UNPAINTED

    Similar to Cub Cadet #  784-5415

    USE 784-5415-0499

    CC-93-001    $45.00

 

45" 450 451 551 Snowblower Hydraulic Lift Bracket

Lift bracket for the newer cyclops tractors and up.  Dimensionally same shape as the original, but made out of grade 50 steel and machined instead of the cast iron original ones.  Grade 8 Stainless Steel hardware.  Used for the lifting of front attachments, snowblowers 450, 451, 551 etc.  Fits the following Models:

1440    1641
1861    1862
1863    1864
1782     2082
2084     2086
2182     2284

Similar to Cub Cadet #  719-3097

USE 603-0027

CC-86-001     $80.00

 

Snow Thrower Wings

Adds 8" total to the width of your cut.  Bolts on with no drilling.  Fits QA-36 and QA42 Snowthrowers. Parts are painted in picture for example.  Parts ship UNPAINTED

CC-76-001    $55.00

 

  • Drift Cutters

  • Attaches to the sides of your snow thrower.  Aids in slicing thru deep drifts and help with guidance.  Bolts on with no drilling.  Fits QA-36 and QA42 Snowthrowers. Parts are painted in picture for example.  Parts ship UNPAINTED

    CC-77-001    $28.00

 

Snow Thrower Drift Hood  36"

Attaches to the top of your snow thrower.  Adds 4" of height to your blower and keeps the snow from coming over the top.  Requires drilling.  Fits QA-36 Snowthrowers. UNPAINTED

CC-78-001    $36.00

 

 

Snow Thrower Drift Hood  42"

Attaches to the top of your snow thrower.  Adds 4" of height to your blower and keeps the snow from coming over the top.  Requires drilling.  Fits QA-36 Snowthrowers. UNPAINTED

CC-78-002    $40.00

 


  • 450 / 451 Super Extensions

  • For use with a 450 / 451 snowblower on a Super Garden Tractor.  Sold in pairs.  UNPAINTED

    CC-78-050    $24.00

 

Snowblower Curved Top Lift Arms

Used when adding a QA snowblower to late model tractors so the chute doesn't hit the hood and also for 82 series tractors for more clearance on installation.  UNPAINTED  Replaces  PN/ IH-548192 R1 and IH-79011 C1

CC-82-001    $32.00

 

450 / 451 Two Stage Snow Blower Skids

Snow thrower skids for models shown below.  Made from 1/4" material and also feature slots for adjustment up and down that the factory ones didn't have. UNPAINTED.  Fits 350, 450, 451 Two Stage as well as, Models 420, 524, 826, 1028

Similar to Cub Cadet #784-5038A  USE 784-5038B-0637

CC-25-003    $54.50

     

Snow Thrower Skids with Feet

Snow thrower skids for models BB36, CW36, QA36, QA36A, QA42A, QA36B, QA42B. UNPAINTED.

Similar to Cub Cadet # IH-475565-R1  USE IH-475565-R2

CC-25-001    $44.50

 

Snowblower Wear Edge - 42"

Wear edge for QA42 QA42A Snow Throwers. UNPAINTED.

Similar to Cub Cadet # IH-397024-R1   USE IH-397024-R2

CC-26-002    $51.50

 

  • Snowblower Wear Edge - 36"

  • Wear edge for QA36, QA36A,QA36B snow throwers. UNPAINTED.

    Similar to Cub Cadet # 397-023-R1      USE IH-397023-R2

    CC-26-001    $48.50

 

Snowblower Wear Edge 45" for 450C

Wear edge for 450C snow Blowers. UNPAINTED.

Similar to Cub Cadet # IH-90430-C1    USE 05598-0637

CC-26-003    $37.50

 
 
This electronic document and is the property of Xtreme Motorworks. It contains material and information that is confidential and proprietary to Xtreme Motorworks. This material and information are protected under federal and/or state trade secret, unfair competition and copyright laws. Any reproduction, use or disclosure without written permission from Xtreme Motorworks is prohibited.  Xtreme Motorworks has no affiliations with any manufacturer listed in this site.

Our Goals

A

Customer Satisfaction

Our goal is to make your shopping experience the best it can be.

B

Top Of The Line Parts

We try to make our parts better that the factory would have made them.

C

Speedy Shipping

We keep inventory on hand so that we can get your order to you as soon as we can.

D

Tested And Tried Parts

We test everything that we invent to make sure that it will be the best for you.